View AX8052F143_8333323.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2015 november, 2015 ? rev. 3 1 publication order number: AX8052F143/d AX8052F143 soc ultra-low power rf-microcontroller for rf carrier frequencies in the range 27 - 1050 mhz overview features soc ultra ? low power advanced narrow ? band rf ? microcontroller for w ireless communication applications ? qfn40 package ? supply range 1.8 v ? 3.6 v ? ? 40 c to 85 c ? ultra ? low power consumption: ? cpu active mode 150 a/mhz ? sleep mode with 256 byte ram retention and wake ? up timer running 900 na ? sleep mode 4 kbyte ram retention and wake ? up timer running 1.5 a ? sleep mode 8 kbyte ram retention and wake ? up timer running 2.2 a ? radio rx ? mode 6.5 ma @ 169 mhz 9.5 ma @ 868 mhz and 433 mhz ? radio tx ? mode at 868 mhz 7.5 ma @ 0 dbm 16 ma @ 10 dbm 48 ma @ 16 dbm ax8052 ? ultra ? low power mcu core compatible with industry standard 8052 instruction set ? down to 500 na wake ? up current ? single cycle/instruction for many instructions ? 64 kbyte in ? system programmable flash ? code protection lock ? 8.25 kbyte sram ? 3 ? wire (1 dedicated, 2 shared) in ? circuit debug interface ? three 16 ? bit timers with output capability ? two 16 ? bit wakeup timers ? two input captures ? two output compares with pwm capability ? 10 ? bit 500 ksample/s analog ? to ? digital converter ? temperature sensor ? two analog comparators ? two uarts ? one general purpose master/slave spi ? two channel dma controller ? multi ? megabit/s aes encryption/decryption engine, supports aes ? 128, aes ? 192 and aes ? 256 with true random number generator (trng) note: the aes engine and the trng require software enabling and support. ? ultra ? low power 10 khz/640 hz wakeup oscillator, with automatic calibration against a precise clock ? internal 20 mhz rc oscillator, with automatic calibration against a precise clock for flexible system clocking ? low frequency tuning fork crystal oscillator for accurate low power time keeping ? brown ? out and power ? on ? reset detection high performance narrow ? band rf transceiver compatible to ax5043 (fsk/msk/4 ? fsk/gfsk/gmsk/ ask/afsk/fm/psk) ? receiver ? carrier frequencies from 27 to 1050 mhz ? data rates from 0.1 kbps to 125 kbps ? optional forward error correction (fec) ? sensitivity without fec ? 135 dbm @ 0.1 kbps, 868 mhz, fsk ? 126 dbm @ 1 kbps, 868 mhz, fsk ? 117 dbm @ 10 kbps, 868 mhz, fsk ? 107 dbm @ 100 kbps, 868 mhz, fsk ? 105 dbm @ 125 kbps, 868 mhz, fsk ? 138 dbm @ 0.1 kbps, 868 mhz, psk ? 130 dbm @ 1 kbps, 868 mhz, psk ? 120 dbm @ 10 kbps, 868 mhz, psk ? 109 dbm @ 100 kbps, 868 mhz, psk ? 108 dbm @ 125 kbps, 868 mhz, psk www.onsemi.com
AX8052F143 www.onsemi.com 2 ? sensitivity with fec ? 137 dbm @ 0.1 kbps, 868 mhz, fsk ? 122 dbm @ 5 kbps, 868 mhz, fsk ? 111 dbm @ 50 kbps, 868 mhz, fsk ? high selectivity receiver with up to 47 db adjacent channel rejection ? 0 dbm maximum input power ? 10% data ? rate error tolerance ? support for antenna diversity with external antenna switch ? short preamble modes allow the receiver to work with as little as 16 preamble bits ? fast state switching times 200 s tx rx switching time 62 s rx tx switching time ? transmitter ? carrier frequencies from 27 to 1050 mhz ? data ? rates from 0.1 kbps to 125 kbps ? high efficiency, high linearity integrated power amplifier ? maximum output power 16 dbm @ 868 mhz 16 dbm @ 433 mhz 16 dbm @ 169 mhz ? power level programmable in 0.5 db steps ? gfsk shaping with bt=0.3 or bt=0.5 ? unrestricted power ramp shaping ? rf frequency generation ? configurable for usage in 27 mhz ? 1050 mhz bands ? rf carrier frequency and fsk deviation programmable in 1 hz steps ? ultra fast settling rf frequency synthesizer for low ? power consumption ? fully integrated rf frequency synthesizer with vco auto ? ranging and band ? width boost modes for fast locking ? configurable for either fully integrated vco, internal vco with external inductor or fully external vco ? configurable for either fully integrated or external synthesizer loop filter for a large range of bandwidths ? channel hopping up to 2000 hops/s ? automatic frequency control (afc) ? flexible antenna interface ? integrated rx/tx switching with differential antenna pins ? mode with differential rx pins and single ? ended tx pin for usage with external pas and for maximum pa efficiency at low output power ? wakeup ? on ? radio ? 640 hz or 10 khz lowest power wake ? up timer ? wake ? up time interval programmable between 98 s and 102 s ? sophisticated radio controller ? antenna diversity and rx/tx switch control ? fully automatic packet reception and transmission without micro ? controller intervention ? supports hdlc, raw, wireless m ? bus frames and arbitrary defined frames ? automatic channel noise level tracking ? s resolution timestamps for exact timing (eg. for frequency hopping systems) ? 256 byte micro ? programmable fifo, optionally supports packet sizes > 256 bytes ? three matching units for preamble byte, sync ? word and address ? ability to store rssi, frequency offset and data ? rate offset with the packet data ? multiple receiver parameter sets allow the use of more aggressive receiver parameters during preamble, dramatically shortening the required preamble length at no sensitivity degradation ? advanced crystal oscillator (rf reference oscillator) ? fast start ? up and lowest power steady ? state xtal oscillator for a wide range of crystals ? integrated tuning capacitors ? possibility of applying an external clock reference (tcxo) applications 27 ? 1050 mhz licensed and unlicensed radio systems ? internet of things ? automatic meter reading (amr) ? security applications ? building automation ? wireless networks ? messaging paging ? compatible with: wireless m ? bus, pocsag, flex, knx, sigfox, z ? wave, enocean ? regulatory regimes: en 300 220 v2.3.1 including the narrow ? band 12.5 khz, 20 khz and 25 khz definitions; en 300 422; fcc part 15.247; fcc part 15.249; fcc part 90 6.25 khz, 12.5 khz and 25 khz
AX8052F143 www.onsemi.com 3 block diagram figure 1. functional block diagram of the AX8052F143 AX8052F143 antp antn if filter and agc pgas agc crystal oscillator typ. 16mhz communication controller & radio interface controller lna divider adc digital if channel filter pa diff de- modulator forward error correction modulator mixer clk16p clk16n rssi radio configuration vdd_ana voltage regulator por, references 256 debug interface axsem 8052 system controller flash 64k aes crypto engine adc comparators spi master/slave uart 1 uart 0 input capture 1 input capture 0 output compare 1 output compare0 timer counter 2 timer counter 1 timer counter 0 gpio pa0 pa1 pa2 pa3 pa4 pa5 reset_n gnd vdd_io 8k ram pc0 pc1 pc2 pc3 pc4 pb0 pb1 pb2 pb3 pb4 pb5 pb6 pb7 i/o multiplexer dbg_en irq req reset, clocks, power i-bus p-bus x-bus sfr-bus dma controller dma req sysclk temp sensor wakeup oscillator rc oscillator tuning fork crystal oscillator wakeup timer 2x rf frequency generation subsystem pa se f out antp1 l1 l2 filt vdd_io f xtal low power oscillator 640 hz/ 10 khz wake on radio encoder framing fifo/packet buffer radio controller timing and packet handling
AX8052F143 www.onsemi.com 4 table 1. pin function descriptions symbol pin(s) type description vdd_ana 1 p analog power output, decouple to neighboring gnd gnd 2 p ground, decouple to neighboring vdd_ana antp 3 a differential antenna input/output antn 4 a differential antenna input/output antp1 5 a single ? ended antenna output gnd 6 p ground, decouple to neighboring vdd_ana vdd_ana 7 p analog power output, decouple to neighboring gnd gnd 8 p ground filt 9 a optional synthesizer filter l2 10 a optional synthesizer inductor l1 11 a optional synthesizer inductor sysclk 12 i/o/pu system clock output pc4 13 i/o/pu general purpose io pc3 14 i/o/pu general purpose io pc2 15 i/o/pu general purpose io pc1 16 i/o/pu general purpose io pc0 17 i/o/pu general purpose io pb0 18 i/o/pu general purpose io pb1 19 i/o/pu general purpose io pb2 20 i/o/pu general purpose io pb3 21 i/o/pu general purpose io pb4 22 i/o/pu general purpose io pb5 23 i/o/pu general purpose io pb6 24 i/o/pu general purpose io, dbg_data pb7 25 i/o/pu general purpose io, dbg_clk dbg_en 26 i/pd in ? circuit debugger enable reset_n 27 i/pu optional reset pin. if this pin is not used it must be connected to vdd_io gnd 28 p ground vdd_io 29 p unregulated power supply pa0 30 i/o/a/pu general purpose io pa1 31 i/o/a/pu general purpose io pa2 32 i/o/a/pu general purpose io pa3 33 i/o/a/pu general purpose io pa4 34 i/o/a/pu general purpose io pa5 35 i/o/a/pu general purpose io vdd_io 36 p unregulated power supply tst1 37 a must be connected to gnd tst2 38 a must be connected to gnd clk16n 39 a crystal oscillator input/output (rf reference oscillator) clk16p 40 a crystal oscillator input/output (rf reference oscillator) gnd center pad p ground on center pad of qfn, must be connected
AX8052F143 www.onsemi.com 5 a = analog input i = digital input signal o = digital output signal pu = pull ? up i/o = digital input/output signal n = not to be connected p = power or ground pd = pull ? down all digital inputs are schmitt trigger inputs, digital input and output levels are l vcmos/l vttl compatible. port a pins (pa0 ? pa7) must not be driven above vdd_io, all other digital inputs are 5 v tolerant. pull ? ups are programmable for all gpio pins. alternate pin functions gpio pins are shared with dedicated input/output signals of on ? chip peripherals. the following table lists the available functions on each gpio pin. table 2. alternate pin functions gpio alternate functions pa0 t0out ic1 adc0 pa1 t0clk oc1 adc1 pa2 oc0 u1rx adc2 compi00 pa3 t1out adc3 lpxtalp pa4 t1clk compo0 adc4 lpxtaln pa5 ic0 u1tx adc5 compi10 pb0 u1tx ic1 extirq0 pb1 u1rx oc1 pb2 ic0 t2out pwramp pb3 oc0 t2clk extirq1 dswake antsel pb4 u0tx t1clk pb5 u0rx t1out pb6 dbg_data pb7 dbg_clk pc0 ssel t0out extirq0 pc1 ssck t0clk compo1 pc2 smosi u0tx pc3 smiso u0rx compo0 pc4 compo1 adctrig extirq1
AX8052F143 www.onsemi.com 6 pinout drawing figure 2. pinout drawing (top view) AX8052F143 qfn40 8 7 6 5 4 3 2 1 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 40 39 38 37 36 35 34 33 32 31 30 29 vdd_ana antp gnd antn antp1 gnd gnd vdd_ana filt l2 l1 sysclk extirq1/adctrig/compo1/pc4 compo0/u0rx/smiso/pc3 u0tx/smosi/pc2 compo1/t0clk/ssck/pc1 extirq0/t0out/ssel/pc0 extirq0/ic1/u1tx/pb0 oc1/u1rx/pb1 pwramp/t2out/ic0/pb2 clk16p clk16n tst1 tst2 vdd_io pa5/adc5/ic0/u1tx/compi10 pa4/adc4/t1clk/compo0/lpxtaln pa3/adc3/t1out/lpxtalp pa2/adc2/oc0/u1rx/compi00 pa1/adc1/t0clk/oc1 pa0/adc0/t0out/ic1 vdd_io gnd reset_n dbg_en pb7/dbg_clk pb6/dbg_data pb5/u0rx/t1out pb4/u0tx/t1clk pb3/oc0/t2clk/extirq1/dswake/ antsel
AX8052F143 www.onsemi.com 7 specifications table 3. absolute maximum ratings symbol description condition min max units vdd_io supply voltage ? 0.5 5.5 v idd supply current 200 ma p tot total power consumption 800 mw p i absolute maximum input power at receiver input antp and antn pins in rx mode 10 dbm i i1 dc current into any pin except antp, antn, antp1 ? 10 10 ma i i2 dc current into pins antp, antn, antp1 ? 100 100 ma i o output current 40 ma v ia input voltage antp, antn, antp1 pins ? 0.5 5.5 v input voltage digital pins ? 0.5 5.5 v v es electrostatic handling hbm ? 2000 2000 v t amb operating temperature ? 40 85 c t stg storage temperature ? 65 150 c t j junction temperature 150 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device function ality should not be assumed, damage may occur and reliability may be affected. 1. exposure to absolute maximum rating conditions for extended periods may affect device reliability. dc characteristics table 4. supplies sym description condition min typ max units t amb operational ambient temperature ? 40 27 85 c vdd io i/o and voltage regulator supply voltage 1.8 3.0 3.6 v vdd io_r1 i/o voltage ramp for reset activation; note 1 ramp starts at vdd_io 0.1 v 0.1 v/ms vdd io_r2 i/o voltage ramp for reset activation; note 1 ramp starts at 0.1 v < vdd_io < 0.7 v 3.3 v/ms v bout brown ? out threshold note 2 1.3 v i ds deep sleep current 100 na i sl256p sleep current, 256 bytes ram retained wakeup from dedicated pin 500 na i sl256 sleep current, 256 bytes ram retained wakeup timer running at 640 hz 900 na i sl4k sleep current, 4.25 kbytes ram retained wakeup timer running at 640 hz 1.5 a i sl8k sleep current, 8.25 kbytes ram retained wakeup timer running at 640 hz 2.2 a i rx current consumption rx rf frequency generation subsystem: internal vco and internal loop ? fiter 868 mhz, datarate 6 kbps 9.5 ma 169 mhz, datarate 6 kbps 6.5 868 mhz, datarate 100 kbps 11 169 mhz, datarate 100 kbps 7.5 i tx ? diff current consumption tx differential 868 mhz, 16 dbm, fsk, note 3 rf frequency generation subsystem: internal vco and internal loop ? filter antenna configuration: differential pa, internal rx/tx switch 48 ma 1. if vdd_io ramps cannot be guaranteed, an external reset circuit is recommended, see the ax8052 application note: power on res et 2. digital circuitry is functional down to typically 1 v. 3. measured with optimized matching networks.
AX8052F143 www.onsemi.com 8 table 4. supplies units max typ min condition description sym i rx ? se current consumption tx single ended 868 mhz, 0 dbm, fsk, note 3 rf frequency generation subsystem: internal vco and internal loop ? filter antenna configuration: single ended pa, external rx/tx switching 7.5 ma i mcu microcontroller running power consumption all peripherals disabled 150 a/ mhz i vsup voltage supervisor run and standby mode 85 a i lpxtal crystal oscillator current (rf reference oscillator) 16 mhz 160 a i lfxtal low frequency crystal oscillator current 32 khz 700 na i rcosc internal oscillator current 20 mhz 210 a i lposc internal low power oscillator current 10 khz 650 na 640 hz 210 na i adc adc current 311 ksample/s, dma 5 mhz 1.1 ma i wor typical wake ? on ? radio duty cycle current 1s, 100 kbps 6 a 1. if vdd_io ramps cannot be guaranteed, an external reset circuit is recommended, see the ax8052 application note: power on res et 2. digital circuitry is functional down to typically 1 v. 3. measured with optimized matching networks. for information on current consumption in complex modes of operation tailored to your application, see the software ax ? radiolab. note on current consumption in tx mode to achieve best output power the matching network has to be optimized for the desired output power and frequency. as a rule of thumb a good matching network produces about 50% efficiency with the AX8052F143 power amplifier although over 90% are theoretically possible. a typical matching network has between 1 db and 2 db loss (p loss ). the theoretical efficiencies are the same for the single ended pa (antp1) and differential pa (antp and antn) therefore only one current value is shown in the table below. we recommend to use the single ended pa for low output power and the differential pa for high power. the differential pa is internally multiplexed with the lna on pins antp and antn. therefore constraints for the rx matching have to be considered for the differential pa matching. the current consumption can be calculated as i tx [ma] 1 pa efficiency 10 p out [dbm] p loss [db] 10 1.8v i offset i offset is about 6 ma for the fully integrated vco at 400 mhz to 1050 mhz, and 3 ma for the vco with external inductor at 169 mhz. the following table shows calculated current consumptions versus output power for p loss = 1 db, pa efficiency = 0.5, i offset = 6 ma at 868 mhz and i offset = 3.5 ma at 169 mhz. table 5. current consumption vs. output power pout [dbm] i txcalc [ma] 868 mhz 169 mhz 0 7.5 4.5 1 7.9 4.9 2 8.4 5.4 3 9.0 6.0 4 9.8 6.8 5 10.8 7.8 6 12.1 9.1 7 13.7 10.7 8 15.7 12.7 9 18.2 15.2 10 21.3 18.3 11 25.3 22.3 12 30.3 27.3 13 36.7 33.7 14 44.6 41.6 15 54.6 51.6 both AX8052F143 power amplifiers run from the regulated vdd_ana supply and not directly from the battery. this has the advantage that the current and output power do not vary much over supply voltage and temperature.
AX8052F143 www.onsemi.com 9 table 6. logic symbol description condition min typ max units digital inputs v t+ schmitt trigger low to high threshold point vdd_io = 3.3 v 1.55 v v t ? schmitt trigger high to low threshold point 1.25 v v il input voltage, low 0.8 v v ih input voltage, high 2.0 v v ipa input voltage range, port a ? 0.5 vdd_io v v ipbc input voltage range, ports b, c ? 0.5 5.5 v i l input leakage current ? 10 10 a r pu programmable pull ? up resistance 65 k digital outputs i oh output current, high ports pa, pb and pc v oh = 2.4 v 8 ma i ol output current, low ports pa, pb and pc v ol = 0.4 v 8 ma i oh output current, high pin sysclk v oh = 2.4 v 4 ma i ol output current, low pin sysclk v ol = 0.4 v 4 ma i oz tri ? state output leakage current ? 10 10 a ac characteristics table 7. crystal oscillator (rf reference oscillator) symbol description condition min typ max units f xtal crystal or frequency note 1, 2, 3 10 16 50 mhz gm osc oscillator transconductance range self ? regulated see note 4 0.2 20 ms c osc programmable tuning capacitors at pins clk16n and clk16p ax5043_xtalcap = 0x00 default 3 pf ax5043_xtalcap = 0x01 8.5 pf ax5043_xtalcap = 0xff 40 pf c osc ? lsb programmable tuning capacitors, increment per lsb of ax5043_xtalcap ax5043_xtalcap = 0x01 ? 0xff 0.5 pf f ext external clock input (tcxo) note 2, 3, 5 10 16 50 mhz rin osc input dc impedance 10 k ndiv sysclk divider ratio f sysclk = f xtal / ndiv sysclk 2 0 2 4 2 10 1. tolerances and start ? up times depend on the crystal used. depending on the rf frequency and channel spacing the ic must be calibrated to the exact crystal frequency using the readings of the register ax5043_trkfreq. 2. the choice of crystal oscillator or tcxo frequency depends on the targeted regulatory regime for tx, see separate documentati on on meeting regulatory requirements. 3. to avoid spurious emission, the crystal or tcxo reference frequency should be chosen so that the rf carrier frequency is not an integer multiple of the crystal or tcxo frequency. 4. the oscillator transconductance is regulated for fastest start ? up time during start ? up and for lowest power curing steady state oscillation. this means that values depend on the crystal used. 5. if an external clock or tcxo is used, it should be input via an ac coupling at pin clk16p wi th the oscillator powered up and ax5043_xtalcap = 000000. for detailed tcxo network recommendations depending on the tcxo output swing refer to the ax5043 application note: use with a tcxo reference clock.
AX8052F143 www.onsemi.com 10 table 8. low ? power oscillator (transceiver wake on radio clock) symbol description condition min typ max units f osc ? slow oscillator frequency slow mode lposc fast = 0 in ax5043_lposcconfig register no calibration 480 640 800 hz internal calibration vs. crystal clock has been performed 630 640 650 f osc ? fast oscillator frequency fast mode lposc fast = 1 in ax5043_lposcconfig register no calibration 7.6 10.2 12.8 khz internal calibration vs. crystal clock has been performed 9.8 10.2 10.8 table 9. rf frequency generation subsystem (synthesizer) symbol description condition min typ max units f ref reference frequency the reference frequency must be chosen so that the rf carrier frequency is not an integer multiple of the reference frequency 10 16 50 mhz dividers ndiv ref reference divider ratio range controlled directly with bits refdiv in register ax5043_pllvcodiv 2 0 2 3 ndiv m main divider ratio range controlled indirectly with register ax5043_freq 4.5 66.5 ndiv rf rf divider range controlled directly with bit rfdiv in register ax5043_ pllvcodiv 1 2 charge pump i cp charge pump current programmable in increments of 8.5 a via register ax5043_pllcpi 8.5 2168 a internal vco (vcosel = 0) f rf rf frequency range rfdiv = 1 400 525 mhz rfdiv = 0 800 1050 f step rf frequency step rfdiv = 1 f ref = 16.000000 mhz 0.98 hz bw synthesizer loop bandwidth the synthesizer loop bandwidth an start ? up time can be programmed with the registers ax5043_pllloop and ax5043_pllcpi. for recommendations see the ax5043 programming manual, the ax ? radiolab software and ax5043 application notes on compliance with regulatory regimes. 50 500 khz t start synthesizer start ? up time if crystal oscillator and reference are running 5 25 s pn868 synthesizer phase noise 868 mhz f ref = 48 mhz 10 khz from carrier ? 95 dbc/hz 1 mhz from carrier ? 120 pn433 synthesizer phase noise 433 mhz f ref = 48 mhz 10 khz from carrier ? 105 dbc/hz 1 mhz from carrier ? 120 vco with external inductors (vcosel = 1, vco2int = 1) f rfrng_lo rf frequency range for choice of l ext values as well as vco gains see figure 3 and figure 4 rfdiv = 1 27 262 mhz f rfrng_hi rfdiv = 0 54 525 pn169 synthesizer phase noise 169 mhz l ext =47 nh (wire wound 0603) ax5043_rfdiv = 0, f ref = 16 mhz note: phase noises can be improved with higher f ref 10 khz from carrier ? 97 dbc/hz 1 mhz from carrier ? 115
AX8052F143 www.onsemi.com 11 table 9. rf frequency generation subsystem (synthesizer) units max typ min condition description symbol external vco (vcosel = 1, vco2int = 0) f rf rf frequency range fully external vco note: the external vco frequency needs to be 2 x f rf 27 1000 mhz v amp differential input amplitude at l1, l2 terminals 0.7 v v inl input voltage levels at l1, l2 terminals 0 1.8 v v ctrl control voltage range available at filt in external loop filter mode 0 1.8 v figure 3. vco with external inductors: typical frequency vs. l ext
AX8052F143 www.onsemi.com 12 figure 4. vco with external inductors: typical k vco vs. l ext the following table shows the typical frequency ranges for frequency synthesis with external vco inductor for different inductor values. table 10. lext [nh] freq [mhz] rfdiv = 0 freq [mhz] rfdiv = 1 pll range 8.2 482 241 0 8.2 437 219 15 10 432 216 0 10 390 195 15 12 415 208 0 12 377 189 15 15 380 190 0 15 345 173 15 18 345 173 0 18 313 157 15 22 308 154 0 22 280 140 14 27 285 143 0 27 258 129 15 33 260 130 0 33 235 118 15 39 245 123 0 39 223 112 14 47 212 106 0 47 194 97 14 56 201 101 0 56 182 91 15 68 178 89 0 68 161 81 15 82 160 80 1 82 146 73 14 100 149 75 1 100 136 68 14 120 136 68 0 120 124 62 14 for tuning or changing of ranges a capacitor can be added in parallel to the inductor.
AX8052F143 www.onsemi.com 13 table 11. transmitter symbol description condition min typ max units sbr signal bit rate 0.1 125 kbps ptx transmitter power @ 868 mhz differential pa, 50 single ended measurement at an sma connector behind the matching network, note 2 ? 10 16 dbm transmitter power @ 433 mhz ? 10 16 transmitter power @ 169 mhz ? 10 16 ptx step programming step size output power note 1 0.5 db dtx temp transmitter power variation vs. temperature ? 40 c to +85 c note 2 0.5 db dtx vdd transmitter power variation vs. vdd_io 1.8 to 3.6 v note 2 0.5 db padj adjacent channel power gfsk bt = 0.5, 500 hz deviation, 1.2 kbps, 25 khz channel spacing, 10 khz channel bw 868 mhz ? 44 dbc 433 mhz ? 51 ptx 868 ? harm2 emission @ 2 nd harmonic 868 mhz, note 2 ? 40 dbc ptx 868 ? harm3 emission @ 3 rd harmonic ? 60 ptx 433 ? harm2 emission @ 2 nd harmonic 433 mhz, note 2 ? 40 dbc ptx 433 ? harm3 emission @ 3 rd harmonic ? 40 1. p out ax5043_txpwrcoeffb 2 12 1 p max 2. 50 single ended measurements at an sma connector behind the matching network. for recommended matching networks see applications section. table 12. receiver sensitivities the table lists typical input sensitivities (without fec) in dbm at the sma connector with the complete matching network for be r=10 ? 3 at 433 or 868 mhz. data rate [kbps] fsk h = 0.66 fsk h = 1 fsk h = 2 fsk h = 4 fsk h = 5 fsk h = 8 fsk h = 16 psk 0.1 sensitivity [dbm] ? 135 ? 134.5 ? 132.5 ? 133 ? 133.5 ? 133 ? 132.5 ? 138 rx bandwidth [khz] 0.2 0.2 0.3 0.5 0.6 0.9 2.1 0.2 deviation [khz] 0.033 0.05 0.1 0.2 0.25 0.4 0.8 1 sensitivity [dbm] ? 126 ? 125 ? 123 ? 123.5 ? 124 ? 123.5 ? 122.5 ? 130 rx bandwidth [khz] 1.5 2 3 6 7 11 21 1 deviation [khz] 0.33 0.5 1 2 2.5 4 8 10 sensitivity [dbm] ? 117 ? 116 ? 113 ? 114 ? 113.5 ? 113 ? 120 rx bandwidth [khz] 15 20 30 50 60 110 10 deviation [khz] 3.3 5 10 20 25 40 100 sensitivity [dbm] ? 107 ? 105.5 ? 109 rx bandwidth [khz] 150 200 100 deviation [khz] 33 50 125 sensitivity [dbm] ? 105 ? 104 ? 108 rx bandwidth [khz] 187.5 200 125 deviation [khz] 42.3 62.5 1. sensitivities are equivalent for 1010 data streams and pn9 whitened data streams. 2. rx bandwidths < 0.9 khz cannot be achieved with an 48 mhz tcxo. a 16 mhz tcxo was used for all measurements at 0.1 kbps.
AX8052F143 www.onsemi.com 14 table 13. receiver symbol description condition min typ max units sbr signal bit rate 0.1 125 kbps is ber868 input sensitivity at ber = 10 ? 3 for 868 mhz operation, continuous data, without fec fsk, h = 0.5, 100 kbps ? 106 dbm fsk, h = 0.5, 10 kbps ? 116 fsk, 500 hz deviation, 1.2 kbps ? 126 psk, 100 kbps ? 109 psk, 10 kbps ? 120 psk, 1 kbps ? 130 is ber868fec input sensitivity at ber = 10 ? 3 , for 868 mhz operation, continuous data, with fec fsk, h = 0.5, 50 kbps ? 111 dbm fsk, h = 0.5, 5 kbps ? 122 fsk, 0.1 kbps ? 137 is per868 input sensitivity at per = 1%, for 868 mhz operation, 144 bit packet data, without fec fsk, h = 0.5, 100 kbps ? 103 dbm fsk, h = 0.5, 10 kbps ? 115 fsk, 500 hz deviation, 1.2 kbps ? 125 is wor868 input sensitivity at per = 1% for 868 mhz operation, wor ? mode, without fec fsk, h= 0.5, 100 kpbs ? 102 dbm il maximum input level full selectivity 0 dbm fsk, reduced selectivity 10 cp 1db input referred compression point 2 tones separated by 100 khz ? 35 dbm rssir rssi control range fsk, 500 hz deviation, 1.2 kbps ? 126 ? 46 db rssis 1 rssi step size before digital channel filter; calculated from register ax5043_agccounter 0.625 db rssis 2 rssi step size behind digital channel filter; calculated from registers ax5043_agccounter, ax5043_trkampl 0.1 db rssis 3 rssi step size behind digital channel filter; reading register ax5043_rssi 1 db sel 868 adjacent channel suppression 25 khz channels , note 1 45 db 100 khz channels, note 1 47 blk 868 blocking at 10 mhz offset note 2 78 db r afc afc pull ? in range the afc pull ? in range can be programmed with the ax5043_maxrfoffset registers. the afc response time can be programmed with the ax5043_freqgaind register. 15 % r droff bitrate offset pull ? in range the bitrate pull ? in range can be programmed with the ax5043_maxdroffset registers. 10 % 1. interferer/channel @ ber = 10 ? 3 , channel level is +3 db above the typical sensitivity, the interfering signal is cw; channel signal is modulated with shaping 2. channel/blocker @ ber = 10 ? 3 , channel level is +3 db above the typical sensitivity, the blocker signal is cw; channel signal is modulated with shaping
AX8052F143 www.onsemi.com 15 table 14. receiver and transmitter settling phases symbol description condition min typ max units t xtal xtal settling time powermodes: powerdown to standby note that t xtal depends on the specific crystal used. 0.5 ms t synth synthesizer settling time powermodes: standby to synthtx or synthrx 40 s t tx tx settling time powermodes: synthtx to fulltx t tx is the time used for power ramping, this can be programmed to be 1 x t bit , 2 x t bit , 4 x t bit or 8 x t bit . note 1 0 1 x t bit 8 x t bit s t rx_init rx initialization time 150 s t rx_rssi rx rssi acquisition time (after t rx_init ) powermodes: synthrx to fullrx modulation (g)fsk note 1 80 + 3 x t bit s t rx_preambl e rx signal acquisition time to valid data rx at full sensitivity/selectivity (after t rx_init ) 9 x t bit 1. t bit depends on the datarate, e.g. for 10 kbps t bit = 100 s table 15. overall state transition times symbol description condition min typ max units t tx_on tx startup time powermodes: standby to fulltx note 1 40 40 + 1 x t bit s t rx_on rx startup time powermodes: standby to fullrx 190 s t rx_rssi rx startup time to valid rssi powermodes: standby to fullrx modulation (g)fsk note 1 270 + 3 x t bit s t rx_data rx startup time to valid data at full sensitivity/selectivity 190 + 9 x t bit s t rxtx rx to tx switching powermodes: fullrx to fulltx 62 s t txrx tx to rx switching (to preamble start) powermodes: fulltx to fullrx 200 t hop frequency hop switch between frequency defined in register ax5043_freqa and ax5043_freqb 30 s 1. t bit depends on the datarate, e.g. for 10 kbps t bit = 100 s
AX8052F143 www.onsemi.com 16 table 16. low frequency crystal oscillator symbol description condition min typ max units f lpxtal crystal frequency 32 150 khz gm lpxosc transconductance oscillator lpxoscgm = 00110 3.5 s lpxoscgm = 01000 4.6 lpxoscgm = 01100 6.9 lpxoscgm = 10000 9.1 rin lpxosc input dc impedance 10 m table 17. internal low power oscillator symbol description condition min typ max units f lposc oscillation frequency lposcfast = 0 factory calibration applied. over the full temperature and voltage range 630 640 650 hz lposcfast = 1 factory calibration applied over the full temperature and voltage range 10.08 10.24 10.39 khz table 18. internal rc oscillator symbol description condition min typ max units f lfrcposc oscillation frequency factory calibration applied. over the full temperature and voltage range 19.8 20 20.2 mhz table 19. microcontroller symbol description condition min typ max units t sysclkl sysclk low 27 ns t sysclkh sysclk high 21 ns t sysclkp sysclk period 47 ns t flwr flash write time 2 bytes 20 s t flpe flash page erase 1 kbytes 2 ms t fle flash secure erase 64 kbytes 10 ms t flend flash endurance: erase cycles 10 000 100 000 cycles t flretroom flash data retention 25 c see figure 5 for the lower limit set by the memory qualification 100 years t flrethot 85 c see figure 5 for the lower limit set by the memory qualification 10
AX8052F143 www.onsemi.com 17 figure 5. flash memory qualification limit for data retention after 10k erase cycles 10 100 1000 10000 100000 15 25 35 45 55 65 75 85 temperature [ c] data retention time [years] table 20. adc / comparator / temperature sensor symbol description condition min typ max units adcsr adc sampling rate gpadc mode 30 500 khz adcsr_t adc sampling rate temperature sensor mode 10 15.6 30 khz adcres adc resolution 10 bits v adcref adc reference voltage & comparator internal reference voltage 0.95 1 1.05 v z adc00 input capacitance 2.5 pf dnl differential nonlinearity 1 lsb inl integral nonlinearity 1 lsb off offset 3 lsb gain_err gain error 0.8 % adc in differential mode v abs_diff absolute voltages & common mode voltage in differential mode at each input 0 vdd_io v v fs_diff01 full swing input for differential signals gain x1 ? 500 500 mv v fs_diff10 gain x10 ? 50 50 mv adc in single ended mode v mid_se mid code input voltage in single ended mode 0.5 v v in_se00 input voltage in single ended mode 0 vdd_io v v fs_se01 full swing input for single ended signals gain x1 0 1 v comparators v comp_abs comparator absolute input voltage 0 vdd_io v v comp_com comparator input common mode 0 vdd_io ? 0.8 v v compoff comparator input offset voltage 20 mv temperature sensor t rng temperature range ? 40 85 c t res temperature resolution 0.1607 c/lsb t err_cal temperature error factory calibration applied ? 2 2 c
AX8052F143 www.onsemi.com 18 circuit description the AX8052F143 is a true single chip narrow ? band, ultra ? low power rf ? microcontroller soc for use in licensed and unlicensed bands ranging from 70 mhz to 1050 mhz. the on ? chip transceiver consists of a fully integrated rf front ? end with modulator and demodulator. base band data processing is implemented in an advanced and flexible communication controller that enables user friendly communication. the AX8052F143 contains a high speed microcontroller compatible to the industry standard 8052 instruction set. it contains 64 kbytes of flash and 8.25 kbytes of internal sram. the AX8052F143 features 3 16 ? bit general purpose timers with capability, 2 output compare units for generating pwm signals, 2 input compare units to record timings of external signals, 2 16 ? bit wakeup timers, a watchdog timer, 2 uart s, a master/slave spi controller, a 10 ? bit 500 ksample/s a/d converter , 2 analog comparators, a temperature sensor, a 2 channel dma controller, and a dedicated aes crypto controller. debugging is aided by a dedicated hardware debug interface controller that connects using a 3 ? wire protocol (1 dedicated wire, 2 shared with gpio) to the pc hosting the debug software. while the radio carrier/lo synthesizer can only be clocked by the crystal oscillator (carrier stability requirements dictate a high stability reference clock in the mhz range), the microcontroller and its peripherals provide extremely flexible clocking options. the system clock that clocks the microcontroller, as well as peripheral clocks, can be selected from one of the following clock sources: the crystal oscillator, an internal high speed 20mhz oscillator, an internal low speed 640 hz/10 khz oscillator, or the low frequency crystal oscillator. prescalers offer additional flexibility with their programmable divide by a power of two capability. to improve the accuracy of the internal oscillators, both oscillators may be slaved to the crystal oscillator. AX8052F143 can be operated from a 1.8 v to 3.6 v power supply over a temperature range of ?40 c to 85 c, it consumes 4 ? 51 ma for transmitting, depending on the output power, 6.8 ? 11 ma for receiving. the AX8052F143 features make it an ideal interface for integration into various battery powered solutions such as ticketing or as transceiver for telemetric applications e.g. in sensors. as primary application, the transceiver is intended for uhf radio equipment in accordance with the european telecommunication standard institute (etsi) specification en 300 220 ? 1 and the us federal communications commission (fcc) standard title 47 cfr part 15 as well as part 90. additionally AX8052F143 is suited for systems targeting compliance with wireless m ? bus standard en 13757 ? 4:2005. wireless m ? bus frame support (s, t, r) is built ? in. the AX8052F143 sends and receives data in frames. this standard operation mode is called frame mode. pre and post ambles as well as checksums can be generated automatically. AX8052F143 supports any data rate from 0.1 kbps to 125 kbps for fsk, msk, 4 ? fsk, gfsk, gmsk and ask modulations. to achieve optimum performance for specific data rates and modulation schemes several register settings to configure the AX8052F143 are necessary, they are outlined in the following, for details see the axsem radiolab software which calculates the necessary register settings and the ax5043 programming manual. the receiver supports multi ? channel operation for all data rates and modulation schemes. microcontroller the ax8052 microcontroller core executes the industry standard 8052 instruction set. unlike the original 8052, many instructions are executed in a single cycle. the system clock and thus the instruction rate can be programmed freely from dc to 20 mhz. memory architecture the AX8052F143 microcontroller features the highest bandwidth memory architecture of its class. figure 6 shows the memory architecture. three bus masters may initiate bus cycles: ? the ax8052 microcontroller core ? the direct memory access (dma) engine ? the advanced encryption standard (aes) engine bus targets include: ? two individual 4 kbytes ram blocks located in x address space, which can be simultaneously accessed and individually shut down or retained during sleep mode ? a 256 byte ram located in internal address space, which is always retained during sleep mode ? a 64 kbytes flash memory located in code space. ? special function registers (sfr) located in internal address space accessible using direct address mode instructions ? additional registers located in x address space (x registers) the upper half of the flash memory may also be accessed through the x address space. this simplifies and makes the software more efficient by reducing the need for generic pointers. note: generic pointers include, in addition to the address, an address space tag. sfr registers are also accessible through x address space, enabling indirect access to sfr registers. this allows driver code for multiple identical peripherals (such as uarts or timers) to be shared. the 4 word 16 bit fully associative cache and a pre ? fetch controller hide the latency of the flash.
AX8052F143 www.onsemi.com 19 figure 6. ax8052 memory architecture arbiter xram 0000 ? 0fff arbiter xram 1000 ? 1fff arbiter x registers 4000 ? 7fff arbiter sfr registers 80 ? ff arbiter iram 00 ? ff arbiter flash 0000 ? ffff aes dma x bus ax8052 sfr bus iram bus code bus cache prefetch the ax8052 memory architecture is fully parallel. all bus masters may simultaneously access different bus tar gets during each system clock cycle. each bus target includes an arbiter that resolves access conflicts. each arbiter ensures that no bus master can be starved. both 4 kbytes ram blocks may be individually retained or switched off during sleep mode. the 256 byte ram is always retained during sleep mode. the aes engine accesses memory 16 bits at a time. it is therefore slightly faster to align its buffers on even addresses. memory map the ax8052, like the other industry standard 8052 compatible microcontrollers, uses a harvard architecture. multiple address spaces are used to access code and data. figure 7 shows the ax8052 memory map. figure 7. ax8052 memory architecture xram flash 0000 ? 007f 0080 ? 00ff 0100 ? 1fff 2000 ? 207f 2080 ? 3f7f 3f80 ? 3fff 4000 ? 4fff 5000 ? 5fff 6000 ? 7fff 8000 ? fbff fc00 ? ffff address calibration data iram iram p (code) space x space i (internal) space direct access indirect access sfr iram sfr rreg rreg (nb) xreg flash calibration data
AX8052F143 www.onsemi.com 20 the ax8052 uses p or code space to access its program. code space may also be read using the movc instruction. smaller amounts of data can be placed in the internal (see note) or data space. a distinction is made in the upper half of the data space between direct accesses (mov reg,addr; mov addr,reg) and indirect accesses (mov reg,@ri; mov @ri,reg; push; pop); direct accesses are routed to the special function registers, while indirect accesses are routed to the internal ram. note: the origin of internal versus external (x) space is historical. external space used to be outside of the chip on the original 8052 microcontrollers. large amounts of data can be placed in the external or x space. it can be accessed using the movx instructions. special function registers, as well as additional microcontroller registers (xreg) and the radio registers (rreg) are also mapped into the x space. detailed documentation of the special function registers (sfr) and additional microcontroller registers can be found in the ax8052 programming manual. the radio registers are documented in the ax5043 programming manual. register addresses given in the ax5043 programming manual are relative to the beginning of rreg, i.e. 0x4000 must be added to these addresses. it is recommended that the axsem provided AX8052F143.h header file is used; radio registers are prefixed with ax5043_ in the AX8052F143.h header file to avoid clashes of same ? name radio registers with ax8052 registers. normally, accessing radio registers through the rreg address range is adequate. since radio register accesses have a higher latency than other ax8052 registers, the ax8052 provides a method for non ? blocking access to the radio registers. accessing the rreg (nb) address range initiates a radio register access, but does not wait for its completion. the details of mechanism is documented in the radio interface section of the ax8052 programming manual. the flash memory is organized as 64 pages of 1 kbytes each. each page can be individually erased. the write word size is 16 bits. the last 1 kbyte page is dedicated to factory calibration data and should not be overwritten. power management the microcontroller power mode can be selected independently from the transceiver. the microcontroller supports the following power modes: table 21. power management pcon register name description 00 running the microcontroller and all peripherals are running. current consumption depends on the system clock frequency and the enabled peripherals and their clock frequency. 01 standby the microcontroller is stopped. all register and memory contents are retained. all peripherals continue to function normally. current consumption is determined by the enabled peripherals. standby is exited when any of the enabled interrupts become active. 10 sleep the microcontroller and its peripherals, except gpio and the system controller, are shut down. their register settings are lost. the internal ram is retained. the external ram is split into two 4 kbyte blocks. software can determine individually for both blocks whether contents of that block are to be retained or lost. sleep can be exited by any of the enabled gpio or system controller interrupts. for most applications this will be a gpio or wakeup timer interrupt. 11 deepsleep the microcontroller, all peripherals and the transceiver are shut down. only 4 bytes of scratch ram are retained. deepsleep can only be exited by tying the pb3 pin low.
AX8052F143 www.onsemi.com 21 clocking figure 8. clock system diagram lposc calib frcosc calib wakeup timer wdt clock monitor prescaler 1,2,4,... frcosc xosc lpxosc lposc interrupt internal reset sysclk glitch free clock switch system clock the system clock can be derived from any of the following clock sources: ? the crystal oscillator (rf reference oscillator, typically 16 mhz, via sysclk) ? the low speed crystal oscillator (typical 32 khz tuning fork) ? the internal high speed rc (20 mhz) oscillator ? the internal low power (640 hz/10 khz) oscillator an additional pre ? scaler allows the selected oscillator to be divided by a power of two. after reset, the microcontroller starts with the internal high speed rc oscillator selected and divided by two. i.e. at start ? up, the microcontroller runs with 10 mhz 10%. clocks may be switched any time by writing to the clkcon register. in order to prevent clock glitches, the switching takes approximately 2(t 1 +t 2 ), where t 1 and t 2 are the periods of the old and the new clock. switching may take longer if the new oscillator first has to start up. internal oscillators start up instantaneously, but crystal oscillators may take a considerable amount of time to start the oscillation. clkstat can be read to determine the clock switching status. a programmable clock monitor resets the clkcon register when no system clock transitions are found during a programmable time interval, thus reverts to the internal rc oscillator. both internal oscillators can be slaved to one of the crystal oscillators to increase the accuracy of the oscillation frequency. while the reference oscillator runs, the internal oscillator is slaved to the reference frequency by a digital frequency locked loop. when the reference oscillator is switched off, the internal oscillator continues to run unslaved with the last frequency setting. reset and interrupts after reset, the microcontroller starts executing at address 0x0000. several events can lead to resetting the microcontroller core: ? por or hardware reset_n pin activated and released ? leaving sleep or deepsleep mode ? watchdog reset ? software reset the reset cause can be determined by reading the pcon register. the microcontroller supports 22 interrupt sources. each interrupt can be individually enabled and can be programmed to have one of two possible priorities. the interrupt vectors are located at 0x0003, 0x000b, ? , 0x00ab.
AX8052F143 www.onsemi.com 22 debugging a hardware debug unit considerably eases debugging compared to other 8052 microcontrollers. it allows to reliably stop the microcontroller at breakpoints even if the stack is smashed. the debug unit communicates with the host pc running the debugger using a 3 wire interface. one wire is dedicated (dbg_en), while two wires are shared with gpio pins (pb6, pb7). when dbg_en is driven high, pb6 and pb7 convert to debug interface pins and the gpio functionality is no longer available. a pin emulation feature however allows bits pinb[7:6] to be set and portb[7:6] and dirb[7:6] to be read by the debugger software. this allows for example switches or leds connected to the pb6, pb7 pins to be emulated in the debugger software whenever the debugger is active. in order to protect the intellectual property of the firmware developer, the debug interface can be locked using a developer ? selectable 64 ? bit key. the debug interface is then disabled and can only be enabled with the knowledge of this 64 ? bit key. therefore, unauthorized persons cannot read the firmware through the debug interface, but debugging is still possible for authorized persons. secure erase can be initiated without key knowledge; secure erase ensures that the main flash array is completely erased before erasing the key, reverting the chip into factory state. the debuglink peripheral looks like an uart to the microcontroller, and allows exchange of data between the microcontroller and the host pc without disrupting program execution. timer, output compare and input capture the AX8052F143 features three general purpose 16 ? bit timers. each timer can be clocked by the system clock, any of the available oscillators, or a dedicated input pin. the timers also feature a programmable clock inversion, a programmable prescaler that can divide by powers of two, and an optional clock synchronization logic that synchronizes the clock to the system clock. all three counters are identical and feature four different counting modes, as well as a mode that can be used to output an analog value on a dedicated digital pin only employing a simple rc lowpass filter. two output compare units work in conjunction with one of the timers to generate pwm signals. two input capture units work in conjunction with one of the timers to measure transitions on an input signal. for software timekeeping, two additional 16 ? bit wakeup timers with 4 16 ? bit event registers are provided, generating an interrupt on match events. uart the AX8052F143 features two universal asynchronous receiver transmitters. they use one of the timers as baud rate generator. w ord length can be programmed from 5 to 9 bits. spi master/slave controller the AX8052F143 features a master/slave spi controller. both 3 and 4 wire spi variants are supported. in master mode, any of the on ? chip oscillators or the system clock may be selected as clock source. an additional prescaler with divide by two capability provides additional clocking flexibility. shift direction, as well as clock phase and inversion, are programmable. adc, analog comparators and temperature sensor the AX8052F143 features a 10 ? bit, 500 ksample/s analog to digital converter. figure 9 shows the block diagram of the adc. the adc supports both single ended and differential measurements. it uses an internal reference of 1 v. 1, 10 and 0.1 gain modes are provided. the adc may digitize signals on pa0 ? pa7, as well as vdd_io and an internal temperature sensor. the user can define four channels which are then converted sequentially and stored in four separate result registers. each channel configuration consists of the multiplexer and the gain setting. the AX8052F143 contains an on ? chip temperature sensor. built ? in calibration logic allows the temperature sensor to be calibrated in c, f or any other user defined temperature scale. the AX8052F143 also features two analog comparators. each comparator can either compare two voltages on dedicated pa pins, or one voltage against the internal 1 v reference. the comparator output can be routed to a dedicated digital output pin or can be read by software. the comparators are clocked with the system clock.
AX8052F143 www.onsemi.com 23 figure 9. adc block diagram temperature sensor adc core clock trigger gain ref vref 1 v vddio pa7 pa6 pa5 pa4 pa3 pa2 pa1 pa0 ppp nnn frcosc lposc xosc lpxosc sysclk system clock one shot free running timer 0 timer 1 timer 2 pc4 adc result acomp1ref acomp1st/pa7/pc1 acomp1in acomp1inv acomp0in acomp0ref acomp0inv acomp0st/pa4/pc3 system clock adcconv adcclksrc x 0.1, x 1, x 10 single ended 0.5 v prescaler 1,2,4,8,... dma controller the AX8052F143 features a dual channel dma engine. each dma channel can either transfer data from xram to almost any peripheral on chip, or from almost any peripheral to xram. both channels may also be cross ? linked for memory ? memory transfers. the dma channels use buffer descriptors to find the buffers where data is to be retrieved or placed, thus enabling very flexible buffering strategies. the dma channels access xram in a cycle steal fashion. they access xram whenever xram is not used by the microcontroller. their priority is lower than the microcontroller, thus interfering very little with the microcontroller. additional logic prevents starvation of the dma controller. aes engine the AX8052F143 contains a dedicated engine for the government mandated advanced encryption standard (aes). it features a dedicated dma engine and reads input data as well as key stream data from the xram, and writes output data into a programmable buffer in the xram. the round number is programmable; the chip therefore supports aes ? 128, aes ? 192, and aes ? 256, as well as higher security proprietary variants. keystream (key expansion) is
AX8052F143 www.onsemi.com 24 performed in software, adding to the flexibility of the aes engine. ecb (electronic codebook), cfb (cipher feedback) and ofb (output feedback) modes are directly supported without software intervention. crystal oscillator and tcxo interface (rf reference oscillator) the AX8052F143 is normally operated with an external tcxo, which is required by most narrow ? band regulation with a tolerance of 0.5 ppm to 1.5 ppm depending on the regulation. the on ? chip crystal oscillator allows the use of an inexpensive quartz crystal as the rf generation subsystem?s timing reference when possible from a regulatory point of view. a wide range of crystal frequencies can be handled by the crystal oscillator circuit. as the reference frequency impacts both the spectral performance of the transmitter as well as the current consumption of the receiver, the choice of reference frequency should be made according to the regulatory regime targeted by the application. application notes for usage of ax5043 in compliance with various regulatory regimes also apply to AX8052F143. the crystal or tcxo reference frequency should be chosen so that the rf carrier frequency is not an integer multiple of the crystal or tcxo frequency. the oscillator circuit is enabled by programming the ax5043_pwrmode register. at power ? up it is enabled. to adjust the circuit?s characteristics to the quartz crystal being used, without using additional external components, the tuning capacitance of the crystal oscillator can be programmed. the transconductance of the oscillator is automatically regulated, to allow for fastest start ? up times together with lowest power operation during steady ? state oscillation. the integrated programmable tuning capacitor bank makes it possible to connect the oscillator directly to pins clk16n and clk16p without the need for external capacitors. it is programmed using bits xtalcap[5:0] in register ax5043_xtalcap. to synchronize the receiver frequency to a carrier signal, the oscillator frequency could be tuned using the capacitor bank however, the recommended method to implement frequency synchronization is to make use of the high resolution rf frequency generation sub ? system together with the automatic frequency control, both are described further down. alternatively a single ended reference (txco, cxo) may be used. the cmos levels should be applied to clk16p via an ac coupling with the crystal oscillator enabled. for detailed tcxo network recommendations depending on tcxo output swing refer to the ax5043 application note: use with a tcxo reference clock. low power oscillator and wake on radio (wor) mode the AX8052F143 transceiver features an internal lowest power fully integrated oscillator. in default mode the frequency of oscillation is 640 hz 1.5%, in fast mode it is 10.2 khz 1.5%. if wake on radio mode is enabled, the receiver wakes up periodically at a user selectable interval, and checks for a radio signal on the selected channel. if no signal is detected, the receiver shuts down again. if a radio signal is detected, and a valid packet is received, the microcontroller is alerted by asserting an interrupt. sysclk output the sysclk pin outputs the rf reference clock signal divided by a programmable integer. divisions from 1 to 2048 are possible. for divider ratios > 1 the duty cycle is 50%. bits sysclk[3:0] in the ax5043_pincfg1 register set the divider ratio. the sysclk output can be disabled. power ? on ? reset (por) and reset_n input AX8052F143 has an integrated power ? on ? reset block which is edge sensitive to vdd_io. for many common application cases no external reset circuitry is required. however, if vdd_io ramps cannot be guaranteed, an external reset circuit is recommended. for detailed recommendations and requirements see the ax8052 application note: power on reset. after por or reset all registers are set to their default values. the reset_n pin contains a weak pull ? up. however, it is strongly recommended to connect the reset_n pin to vdd_io if not used, for additional robustness. the AX8052F143 can be reset by software as well. the microcontroller is reset by writing 1 to the swreset bit of the pcon register. the transceiver can be reset by first writing 1 and then 0 to the rst bit in the ax5043_pwrmode register.
AX8052F143 www.onsemi.com 25 ports figure 10. port pin schematic vddio portx.y dirx.y special function paltx.y pinx read clock pinx.y interrupt intchgx.y analogx.y 65 k figure 10 shows the gpio logic. the dir register bit determines whether the port pin acts as an output (1) or an input (0). if configured as an output, the palt register bit determines whether the port pin is connected to a peripheral output (1), or used as a gpio pin (0). in the latter case, the port register bit determines the port pin drive value. if configured as an input, the port register bit determines whether a pull ? up resistor is enabled (1) or disabled (0). inputs have chmitt ? trigger characteristic. port a inputs may be disabled by setting the analoga register bit; this prevents additional current consumption if the voltage level of the port pin is mid ? way between logic low and logic high, when the pin is used as an analog input. port a, b and c pins may interrupt the microcontroller if their level changes. the intchg register bit enables the interrupt. the pin register bit reflects the value of the port pin. reading the pin register also resets the interrupt if interrupt on change is enabled. pwramp and antsel pwramp functionality is available on pb2 if paltradio bit 6 and dirb bit 2 are set. antsel functionality is available on pb3 if paltradio bit 7 and dirb bit 3 are set. if these pins should be set to high ? impedance, it must be done by clearing the corresponding dirb bit, not by setting ax5043_pinfuncpwramp or ax5043_pinfuncantsel to z.
AX8052F143 www.onsemi.com 26 transceiver the transceiver block is controllable through its registers, which are mapped into the x data space of the micro ? controller. the transceiver block features its own 4 word 10 bit fifo. the microcontroller can either be interrupted at a programmable fifo fill level, or one of the dma channels can be instructed to transfer between xram and the transceiver fifo. rf frequency generation subsystem the rf frequency generation subsystem consists of a fully integrated synthesizer, which multiplies the reference frequency from the crystal oscillator to get the desired rf frequency. the advanced architecture of the synthesizer enables frequency resolutions of 1 hz, as well as fast settling times of 5 ? 50 s depending on the settings (see section ac characteristics). fast settling times mean fast start ? up and fast rx/tx switching, which enables low ? power system design. for receive operation the rf frequency is fed to the mixer, for transmit operation to the power ? amplifier. the frequency must be programmed to the desired carrier frequency. the synthesizer loop bandwidth can be programmed, this serves three purposes: 1. start ? up time optimization, start ? up is faster for higher synthesizer loop bandwidths 2. tx spectrum optimization, phase ? noise at 300 khz to 1 mhz distance from the carrier improves with lower synthesizer loop bandwidths 3. adaptation of the bandwidth to the data ? rate. for transmission of fsk and msk it is required that the synthesizer bandwidth must be in the order of the data ? rate. vco an on ? chip vco converts the control voltage generated by the charge pump and loop filter into an output frequency. this frequency is used for transmit as well as for receive operation. the frequency can be programmed in 1 hz steps in the ax5043_freq registers. for operation in the 433 mhz band, the rfdiv bit in the ax 5043_pllvcodiv register must be programmed. the fully integrated vco allows to operate the device in the frequency ranges 800 ? 1050 mhz and 400 ? 520 mhz. the carrier frequency range can be extended to 54 ? 525 mhz and 27 ? 262 mhz by using an appropriate external inductor between device pins l1 and l2. the bits vco2int and vcosel in the ax 5043_pllvcodiv register must be set high to enter this mode. it is also possible to use a fully external vco by setting bits vco2int = 0 and vcosel = 1 in the ax5043_pllvcodiv register. a differential input at a frequency of double the desired rf frequency must be input at device pins l1 and l2. the control voltage for the vco can be output at device pin filt when using external filter mode. the voltage range of this output pin is 0 ? 1.8 v. this mode of operation is recommended for special applications where the phase noise requirements are not met when using the fully internal vco or the internal vco with external inductor. vco auto ? ranging the AX8052F143 has an integrated auto ? ranging function, which allows to set the correct vco range for specific frequency generation subsystem settings automatically. typically it has to be executed after power ? up. the function is initiated by setting the rng_start bit in the ax5043_pllranginga or ax5043_pllrangingb register. the bit is readable and a 0 indicates the end of the ranging process. setting rng_start in the ax5043_pllranginga register ranges the frequency in ax5043_freqa, while setting rng_start in the ax5043_pllrangingb register ranges the frequency in ax5043_freqb. the rngerr bit indicates the correct execution of the auto ? ranging. vco auto ? ranging works with the fully integrated vco and with the internal vco with external inductor. loop filter and charge pump the AX8052F143 internal loop filter configuration together with the charge pump current sets the synthesizer loop band width. the internal loop ? filter has three configurations that can be programmed via the register bits flt[1:0] in registers ax5043_pllloop or ax5043_pllloopboost the charge pump current can be programmed using register bits pllcpi[7:0] in registers ax5043_pllcpi or ax5043_pllcpiboost. synthesizer bandwidths are typically 50 ? 500 khz depending on the ax5043_pllloop or ax5043_pllloopboost settings, for details see the section: ac characteristics. the AX8052F143 can be setup in such a way that when the synthesizer is started, the settings in the registers ax5043_pllloopboost and ax5043_pllcpiboost are applied first for a programmable duration before reverting to the settings in ax5043_pllloop and ax5043_pllcpi . this feature enables automated fastest start ? up. setting bits fl t[1:0] = 00 bypasses the internal loop filter and the vco control voltage is output to an external loop filter at pin filt. this mode of operation is recommended for achieving lower bandwidths than with the internal loop filter and for usage with a fully external vco. registers
AX8052F143 www.onsemi.com 27 table 22. rf frequency generation registers register bits purpose ax5043_pllloop ax5043_pllloopboost flt[1:0] synthesizer loop filter bandwidth and selection of external loop filter, recommended usage is to increase the bandwidth for faster settling time, bandwidth increases of factor 2 and 5 are possible. ax5043_pllcpi ax5043_pllcpiboost synthesizer charge pump current, recommended usage is to decrease the bandwidth (and improve the phase ? noise) for low data ? rate transmissions. ax5043_pllvcodiv refdiv sets the synthesizer reference divider ratio. rfdiv sets the synthesizer output divider ratio. vcosel selects either the internal or the external vco vco2int selects either the internal vco inductor or an external inductor between pins l1 and l2 ax5043_freqa, ax5043_freqb programming of the carrier frequency ax5043_pllranginga, ax5043_pllrangingb initiate vco auto ? ranging and check results rf input and output stage (antp/antn/antp1) the AX8052F143 has two main antenna interface modes: 1. both rx and tx use differential pins antp and antn. rx/tx switching is handled internally. this mode is recommended for highest output powers, highest sensitivities and for direct connection to dipole antennas. also see figure 15. 2. rx uses the differential antenna pins antp and antn. tx uses the single ended antenna pin antp1. rx/tx switching is handled externally. this can be done either with an external rx/tx switch or with a direct tie configuration. this mode is recommended for low output powers at high efficiency figure 18 and for usage with external power amplifiers figure 17. pin pb2 can be used to control an external rx/tx switch when operating the device together with an external pa (figure 17). pin pb3 can be used to control an external antenna switch when receiving with two antennas (figure 19). when antenna diversity is enabled, the radio controller will, when not in the middle of receiving a packet, periodically probe both antennas and select the antenna with the highest signal strength. the radio controller can be instructed to periodically write both rssi values into the fifo. antenna diversity mode is fully automatic. lna the lna amplifies the differential rf signal from the antenna and buffers it to drive the i/q mixer. an external matching network is used to adapt the antenna impedance to the ic impedance. a dc feed to gnd must be provided at the antenna pins. pa in tx mode the pa drives the signal generated by the frequency generation subsystem out to either the dif ferential antenna terminals or to the single ended antenna pin. the antenna terminals are chosen via the bits txdiff and txse in register ax5043_modecfga. the output power of the pa is programmed via the register ax5043_txpwrcoeffb. the pa can be digitally pre ? distorted for high linearity. the output amplitude can be shaped (raised cosine), this mode is selected with bit amplshape in register ax5043_modecfga pa ramping is programmable in increments of the bit time and can be set to 1 ? 8 bit times via bits slowramp in register ax5043_modecfga . output power as well as harmonic content will depend on the external impedance seen by the pa. digital if channel filter and demodulator the digital if channel filter and the demodulator extract the data bit ? stream from the incoming if signal. they must be programmed to match the modulation scheme as well as the data ? rate. inaccurate programming will lead to loss of sensitivity. the channel filter offers bandwidths of 995 hz up to 221 khz. the axsem radiolab software calculates the necessary register settings for optimal performance. an overview of the registers involved is given in the following table as reference, for details see the ax5043 programming manual. the register setups typically must be done once at power ? up of the device. registers
AX8052F143 www.onsemi.com 28 table 23. channel filter and demodulator registers register remarks ax5043_decimation this register programs the bandwidth of the digital channel filter. ax5043_rxdatarate2 ? ax5043_rxdatarate0 these registers specify the receiver bit rate, relative to the channel filter bandwidth. ax5043_maxdroffset2 ? ax5043_maxdroffset0 these registers specify the maximum possible data rate offset ax5043_maxrfoffset2 ? ax5043_maxrfoffset0 these registers specify the maximum possible rf frequency offset ax5043_timegain, ax5043_drgain these registers specify the aggressiveness of the receiver bit timing recovery. more aggressive settings allow the receiver to synchronize with shorter preambles, at the expense of more timing jitter and thus a higher bit error rate at a given signal ? to ? noise ratio. ax5043_modulation this register selects the modulation to be used by the transmitter and the receiver, i.e. whether ask, fsk should be used. ax5043_phasegain, ax5043_freqgaina, ax5043_freqgainb, ax5043_freqgainc, ax5043_freqgaind, ax5043_amplgain these registers control the bandwidth of the phase, frequency offset and amplitude tracking loops. ax5043_agcgain this register controls the agc (automatic gain control) loop slopes, and thus the speed of gain adjustments. the faster the bit ? rate, the faster the agc loop should be. ax5043_txrate these registers control the bit rate of the transmitter. ax5043_fskdev these registers control the frequency deviation of the transmitter in fsk mode. the receiver does not explicitly need to know the frequency deviation, only the channel filter bandwidth has to be set wide enough for the complete modulation to pass. encoder the encoder is located between the framing unit, the demodulator and the modulator. it can optionally transform the bit ? stream in the following ways: ? it can invert the bit stream. ? it can perform differential encoding. this means that a zero is transmitted as no change in the level, and a one is transmitted as a change in the level. ? it can perform manchester encoding. manchester encoding ensures that the modulation has no dc content and enough transitions (changes from 0 to 1 and from 1 to 0) for the demodulator bit timing recovery to function correctly, but does so at a doubling of the data rate. ? it can perform spectral shaping (also know as whitening). spectral shaping removes dc content of the bit stream, ensures transitions for the demodulator bit timing recovery, and makes sure that the transmitted spectrum does not have discrete lines even if the transmitted data is cyclic. it does so without adding additional bits, i.e. without changing the data rate. spectral shaping uses a self synchronizing feedback shift register. the encoder is programmed using the register ax5043_encoding, details and recommendations on usage are given in the ax5043 programming manual. framing and fifo most radio systems today group data into packets. the framing unit is responsible for converting these packets into a bit ? stream suitable for the modulator, and to extract packets from the continuous bit ? stream arriving from the demodulator. the framing unit supports two different modes: ? packet modes ? raw modes the microcontroller communicates with the framing unit through a 256 byte fifo. data in the fifo is organized in chunks. the chunk header encodes the length and what data is contained in the payload. chunks may contain packet data, but also rssi, frequency offset, timestamps, etc. the AX8052F143 contains one fifo. its direction is switched depending on whether transmit or receive mode is selected. the fifo can be operated in polled or interrupt driven modes. in polled mode, the microcontroller must periodically read the fifo status register or the fifo count register to determine whether the fifo needs servicing. in interrupt mode empty, not empty, full, not full and programmable level interrupts are provided. interrupts are acknowledged by removing the cause for the interrupt, i.e. by emptying or filling the fifo. to lower the interrupt load on the microcontroller, one of the dma channels may be instructed to transfer data
AX8052F143 www.onsemi.com 29 between the transceiver fifo and the xram memory. this way, much larger buffers can be realized in xram, and interrupts need only be serviced if the larger xram buf fers fill or empty. packet modes the AX8052F143 offers different packet modes. for arbitrary packet sizes hdlc is recommended since the flag and bit ? stuffing mechanism. the AX8052F143 also offers packet modes with fixed packet length with a byte indicating the length of the packet. in packet modes a crc can be computed automatically. hdlc mode is the main framing mode of the AX8052F143. in this mode, the AX8052F143 performs automatic packet delimiting, and optional packet correctness check by inserting and checking a cyclic redundancy check (crc) field. note: hdlc mode follows high ? level data link control (hdlc, iso 13239) protocol. the packet structure is given in the following table. table 24. hdlc packet structure flag address control information fcs (optional flag) 8 bit 8 bit 8 or 16 bit variable length, 0 or more bits in multiples of 8 16 / 32 bit 8 bit hdlc packets are delimited with flag sequences of content 0x7e. in AX8052F143 the meaning of address and control is user defined. the frame check sequence (fcs) can be programmed to be crc ? ccitt, crc ? 16 or crc ? 32. the receiver checks the crc, the result can be retrieved from the fifo, the crc is appended to the received data. in wireless m ? bus mode, the packet structure is given in the following table. note: wireless m ? bus mode follows en13757 ? 4 table 25. wireless m ? bus packet structure preamble l c m a fcs optional data block (optionally repeated with fcs) fcs variable 8 bit 8 bit 8 bit 8 bit 16 bit 8 ? 96 bit 16 bit for details on implementing a hdlc communication as well as wireless m ? bus please use the axsem radiolab software and see the ax5043 programming manual. raw modes in raw mode, the AX8052F143 does not perform any packet delimiting or byte synchronization. it simply serializes transmit bytes and de ? serializes the received bit ? stream and groups it into bytes. this mode is ideal for implementing legacy protocols in software. raw mode with preamble match is similar to raw mode. in this mode, however, the receiver does not receive anything until it detects a user programmable bit pattern (called the preamble) in the receive bit ? stream. when it detects the preamble, it aligns the de ? serialization to it. the preamble can be between 4 and 32 bits long. rx agc and rssi AX8052F143 features three receiver signal strength indicators (rssi): 1. rssi before the digital if channel filter. the gain of the receiver is adjusted in order to keep the analog if filter output level inside the working range of the adc and demodulator. the register ax5043_agccounter contains the current value of the agc and can be used as an rssi. the step size of this rssi is 0.625 db. the value can be used as soon as the rf frequency generation sub ? system has been programmed. 2. rssi behind the digital if channel filter. the register ax5043_rssi contains the current value of the rssi behind the digital if channel filter. the step size of this rssi is 1 db. 3. rssi behind the digital if channel filter high accuracy. the demodulator also provides amplitude information in the ax5043_trk_amplitude register. by combining both the ax5043_agccounter and the ax5043_trk_amplitude registers, a high resolution (better than 0.1 db) rssi value can be computed at the expense of a few arithmetic operations on the micro ? controller. the axsem radiolab software calculates the necessary register settings for best performance. modulator depending on the transmitter settings the modulator generates various inputs for the pa:
AX8052F143 www.onsemi.com 30 table 26. modulations modulation bit = 0 bit = 1 main lobe bandwidth max. bitrate ask pa off pa on bw = bitrate 125 kbit/s fsk/msk/gfsk/gmsk f = ? f deviation f = +f deviation bw = (1 + h) ? bitrate 125 kbit/s psk = 0 = 180 bw = bitrate 125 kbit/s h = modulation index. it is the ratio of the deviation compared to the bit ? rate; f deviation = 0.5 ? h ? bitrate, AX8052F143 can demodulate signals with h < 32. ask = amplitude shift keying fsk = frequency shift keying msk= minimum shift keying; msk is a special case of fsk, where h = 0.5, and therefore f deviation = 0.25 ? bitra te; the advantage of msk over fsk is that it can be demodulated more robustly. psk = phase shift keying all modulation schemes, except 4 ? fsk, are binary. amplitude can be shaped using a raised cosine waveform. amplitude shaping will also be performed for constant amplitude modulation ((g)fsk, (g)msk) for ramping up and down the pa. amplitude shaping should always be enabled. frequency shaping can either be hard (fsk, msk), or gaussian (gmsk, gfsk), with selectable bt = 0.3 or bt = 0.5. table 27. 4 ? fsk modulation modulation dibit = 00 dibit = 01 dibit = 11 dibit = 10 main lobe bandwidth max. bitrate 4 ? fsk f = ? 3f deviation f = ? f deviation f = +f deviation f = +3f deviation bw = (1 + 3 h) ? bitrate 125 kbit/s 4 ? fsk frequency shaping is always hard. automatic frequency control (afc) the AX8052F143 features an automatic frequency tracking loop which is capable of tracking the transmitter frequency within the rx filter band width. on top of that the AX8052F143 has a frequency tracking register ax5043_trkrffreq to synchronize the receiver frequency to a carrier signal. for afc adjustment, the frequency offset can be computed with the following formula: f ax5043_trkrffreq 2 32 f xtal pwrmode register the AX8052F143 transceiver features its own independent power management, independent from the microcontroller. while the microcontroller power mode is controlled through the pcon register, the ax5043_pwrmode register controls which parts of the transceiver are operating. table 28. pwrmode register ax5043_pwrmode register name description 0000 powerdown all digital and analog functions, except the register file, are disabled. the core supply voltages are switched off to conserve leakage power. register contents are preserved. access to the fifo is not possible and the contents are not preserved. powerdown mode is only entered once the fifo is empty. 0001 deepsleep the transceiver is fully turned off. all digital and analog functions are disabled. all register contents are lost. to leave deepsleep mode the pin sel has to be pulled low. this will initiate startup and reset of the transceiver. then the miso line should be polled, as it will be held low during initialization and will rise to high at the end of the initialization, when the chip becomes ready for operation. it is recommended to use the functions ax5043_enter_deepsleep() and ax5043_wakeup_deepsleep() provided in libmf 0101 standby the crystal oscillator and the reference are powered on; receiver and transmitter are off. register contents are preserved and accessible. access to the fifo is not possible and the contents are not preserved. standby is only entered once the fifo is empty. 0110 fifo the reference is powered on. register contents are preserved and accessible. access to the fifo is possible and the contents are preserved.
AX8052F143 www.onsemi.com 31 table 28. pwrmode register ax5043_pwrmode register description name 1000 synthrx the synthesizer is running on the receive frequency. transmitter and receiver are still off. this mode is used to let the synthesizer settle on the correct frequency for receive. 1001 fullrx synthesizer and receiver are running. 1011 wor receiver wakeup ? on ? radio mode. the mode the same as powerdown, but the 640 hz internal low power oscillator is running. 1100 synthtx the synthesizer is running on the transmit frequency. transmitter and receiver are still off. this mode is used to let the synthesizer settle on the correct frequency for transmit. 1101 fulltx synthesizer and transmitter are running. do not switch into this mode before the synthesizer has completely settled on the transmit frequency (in synthtx mode), otherwise spurious spectral transmissions will occur. table 29. a typical ax5043_pwrmode sequence for a transmit session step pwrmode remarks 1 powerdown 2 standby the settling time is dominated by the crystal used, typical value 3ms. 3 fulltx data transmission 4 powerdown table 30. a typical ax5043_pwrmode sequence for a receive session step pwrmode [3:0] remarks 1 powerdown 2 standby the settling time is dominated by the crystal used, typical value 3ms. 3 fullrx data reception 4 powerdown voltage regulator the AX8052F143 transceiver uses its own dedicated on ? chip voltage regulator system to create stable supply voltages for the internal circuitry from the primary supply vdd_io. the i/o level of the digital pins is vdd_io. pins vdd_ana are supplied for external decoupling of the power supply used for the on ? chip pa. the voltage regulator system must be set into the appropriate state before receive or transmit operations can be initiated. this is handled automatically when programming the device modes via the ax5043_pwrmode register. register ax5043_powstat contains status bits that can be read to check if the regulated voltages are ready (bit svio) or if vdd_io has dropped below the brown ? out level of 1.3 v (bit ssum). in power ? down mode the core supply voltages for digital and analog functions are switched off to minimize leakage power. most register contents are preserved but access to the fifo is not possible and fifo contents are lost. in deep ? sleep mode all supply voltages are switched off. all digital and analog functions are disabled. all register contents are lost.
AX8052F143 www.onsemi.com 32 application information typical application diagrams connecting to debug adapter figure 11. typical application diagram with connection to the debug adapter vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 100pf 1uf dbg_en dbg_rt_n gnd dbg_data dbg_clk gnd dbg_vdd jumper jp1 1 2 3 4 5 6 7 8 rf reference xtal 32 khz xtal debug adapter connector short jumper jp1 ? 1 if it is desired to supply the target board from the debug adapter (50 ma max). connect the bottom exposed pad of the AX8052F143 to ground. if the debugger is not running, pb6 and pb7 are not driven by the debug adapter. if the debugger is running, the pb6 and pb7 values that the software reads may be set using the pin emulation feature of the debugger. pb3 is driven by the debugger only to bring the AX8052F143 out of deep sleep. it is high impedance otherwise. the 32 khz crystal is optional, the fast crystal at pins clk16n and clk16p is used as reference frequency for the rf rx/tx. crystal load capacitances should be chosen according to the crystal?s datasheet. at pins clk16n and clk16p they the internal programmable capacitors may be used, at pins pa3 and pa4 capacitors must be connected externally.
AX8052F143 www.onsemi.com 33 match to 50 for differential antenna pins (868 / 433 mhz rx / tx operation) figure 12. structure of the differential antenna interface for tx/rx operation to 50 single ? ended equipment or antenna ic antenna pins lt1 lc1 lb1 ct1 cc1 cm1 lt 2 lc2 ct2 cc2 cm2 cb2 lb2 cf lf ca ca optional filter stage to suppress tx harmonics 50 single ? ended equipment or antenna table 31. typical component values frequency band lc1,2 [nh] cc1,2 [pf] ct1,2 [pf] lt1,2 [nh] cm1 [pf] cm2 [pf] lb1,2 [nh] cb2 [pf] cf [pf] optional lf [nh] optional ca [pf] optional 868 / 915 mhz 18 nc 2.7 18 6.2 3.6 12 2.7 nc 0 nc 433 mhz 100 nc 4.3 43 11 5.6 27 5.1 nc 0 nc 470 mhz 100 nc 3.9 33 4.7 nc 22 4.7 nc 0 nc 169 mhz 150 10 10 120 12 nc 68 12 6.8 30 27 match to 50 for single ? ended antenna pin (868 / 915 / 433 mhz tx operation) figure 13. structure of the single ? ended antenna interface for tx operation to 50 single ? ended equipment or antenna ic antenna pin lt lc ct cc cf1 lf1 ca1 ca2 50 single ? ended equipment or antenna table 32. typical component values frequency band lc [nh] cc [pf] ct [pf] lt [nh] cf1 [pf] lf1 [nh] ca1 [pf] ca2 [pf] 868 / 915 mhz 18 nc 2.7 18 3.6 2.2 3.6 nc 433 mhz 100 nc 4.3 43 6.8 4.7 5.6 nc
AX8052F143 www.onsemi.com 34 match to 50 for single ? ended antenna pin (169 mhz tx operation) figure 14. structure of the single ? ended antenna interface for tx operation to 50 single ? ended equipment or antenna ic antenna pin lt lc ct cc cf1 lf1 ca1 50 single ? ended equipment or antenna ca2 cf2 lf2 ca3 table 33. typical component values frequency band lc [nh] cc [pf] ct [pf] lt [nh] cf1 [pf] lf1 [nh] cf2 [pf] lf2 [nh] ca1 [pf] ca2 [pf] ca3 [pf] 169 mhz 150 2.2 22 120 4.7 39 1.8 47 33 47 15 using a dipole antenna and the internal tx/rx switch figure 15. typical application diagram with dipole antenna and internal tx/rx switch vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143
AX8052F143 www.onsemi.com 35 using a single ? ended antenna and the internal tx/rx switch figure 16. typical application diagram with single ? ended antenna and internal tx/rx switch vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 50
AX8052F143 www.onsemi.com 36 using an external high ? power pa and an external tx/rx switch figure 17. typical application diagram with single ? ended antenna, external pa and external antenna switch vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 pa tx/rx switch 50
AX8052F143 www.onsemi.com 37 using the single ? ended pa figure 18. typical application diagram with single ? ended antenna, single ? ended internal pa, without rx/tx switch vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 50 note: for details and recommendations on implementing this configuration refer to the AX8052F143 application note: 0 dbm / 8 ma tx and 9.5 ma rx configuration for the 868 mhz band.
AX8052F143 www.onsemi.com 38 using two antenna figure 19. typical application diagram with two single ? ended antenna and external antenna switch antenna switch vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 pb3 pb3
AX8052F143 www.onsemi.com 39 using an external vco inductor figure 20. typical application diagram with external vco inductor lvco vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143
AX8052F143 www.onsemi.com 40 using an external vco figure 21. typical application diagram with external vco vctrl outp outn en vco vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143
AX8052F143 www.onsemi.com 41 using a tcxo figure 22. typical application diagram with a tcxo tcxo c1_tcxo c2_tcxo en_tcxo vdd_ana gnd antp antn antp1 gnd vdd_ana clk16p clk16n tst1 tst2 vdd_io pa5 pa4 gnd reset_n dbg_en pb7 pb6 pb5 pb4 filt l2 l1 sysclk pc3 pc2 pc4 gnd pb3 pa3 pa2 pa1 pa0 vdd_io pc1 pc0 pb0 pb2 pb1 AX8052F143 pb2 pb2 note: for detailed tcxo network recommendations depending on tcxo output swing refer to the ax5043 application note: use with a tcxo reference clock.
AX8052F143 www.onsemi.com 42 qfn40 package information package outline qfn40 5 x 7 mm figure 23. package outline qfn40 5 x 7 mm notes: 1. ?e? represents the basic terminal pitch 2. datum ?c? is the mounting surface with which the package is in contact. 3. ?3? specifies the vertical shift of the flat part of each terminal from the mounting surface. 4. dimension ?a? includes package warpage. 5. dimension ?b? applies to the metallised terminal and is measured between 0.15 to 0.30 mm from the terminal tip. if the terminal has the optional radius on the other end of the terminal, the dimension ?b? should not be measured in the radius are 6. package dimension take reference from jedec mo ? 220 7. awlyyww is the packaging lot code 8. v is the device version 9. rohs AX8052F143 ? v awlyyww on
AX8052F143 www.onsemi.com 43 qfn40 soldering profile figure 24. qfn40 soldering profile preheat reflow cooling t p t l t smax t smin t s t l t p t 25 c to peak temperature time 25 c table 34. profile feature pb ? free process average ramp ? up rate 3 c/s max. preheat preheat temperature min t smin 150 c temperature max t smax 200 c time (t smin to t smax ) t s 60 ? 180 sec time 25 c to peak temperature t 25 c to peak 8 min max. reflow phase liquidus temperature t l 217 c time over liquidus temperature t l 60 ? 150 s peak temperature t p 260 c time within 5 c of actual peak temperature t p 20 ? 40 s cooling phase ramp ? down rate 6 c/s max. 1. all temperatures refer to the top side of the package, measured on the the package body surface.
AX8052F143 www.onsemi.com 44 qfn40 recommended pad layout 1. pcb land and solder masking recommendations are shown in figure 25. figure 25. pcb land and solder mask recommendations a = clearance from pcb thermal pad to solder mask opening, 0.0635 mm minimum b = clearance from edge of pcb thermal pad to pcb land, 0.2 mm minimum c = clearance from pcb land edge to solder mask opening to be as tight as possible to ensure that some solder mask remains between pcb pads. d = pcb land length = qfn solder pad length + 0.1 mm e = pcb land width = qfn solder pad width + 0.1 mm 2. thermal vias should be used on the pcb thermal pad (middle ground pad) to improve thermal conductivity from the device to a copper ground plane area on the reverse side of the printed circuit board. the number of vias depends on the package thermal requirements, as determined by thermal simulation or actual testing. 3. increasing the number of vias through the printed circuit board will improve the thermal conductivity to the reverse side ground plane and external heat sink. in general, adding more metal through the pc board under the ic will improve operational heat transfer, but will require careful attention to uniform heating of the board during assembly. assembly process stencil design & solder paste application 1. stainless steel stencils are recommended for solder paste application. 2. a stencil thickness of 0.125 ? 0.150 mm (5 ? 6 mils) is recommended for screening. 3. for the pcb thermal pad, solder paste should be printed on the pcb by designing a stencil with an array of smaller openings that sum to 50% of the qfn exposed pad area. solder paste should be applied through an array of squares (or circles) as shown in figure 26. 4. the aperture opening for the signal pads should be between 50 ? 80% of the qfn pad area as shown in figure 27. 5. optionally, for better solder paste release, the aperture walls should be trapezoidal and the corners rounded. 6. the fine pitch of the ic leads requires accurate alignment of the stencil and the printed circuit board. the stencil and printed circuit assembly should be aligned to within + 1 mil prior to application of the solder paste. 7. no ? clean flux is recommended since flux from underneath the thermal pad will be difficult to clean if water ? soluble flux is used. figure 26. solder paste application on exposed pad
AX8052F143 www.onsemi.com 45 figure 27. solder paste application on pins minimum 50% coverage 62% coverage maximum 80% coverage table 35. device versions device marking ax8052 version ax5043 version AX8052F143 ? 1 1 1 AX8052F143 ? 2 1c 1 on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent ? marking.pdf. scillc reserves the right to make changes without further notice to any products herein. scillc makes no warrant y, representation or guarantee regarding the suitability of it s products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer s hall indemnify and hold scillc and its officers , employees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5817 ? 1050 AX8052F143/d literature fulfillment : literature distribution center for on semiconductor 19521 e. 32nd pkwy, aurora, colorado 80011 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of AX8052F143

	To Download AX8052F143 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .